Difference between revisions of "Nextelco:ASA2"
From its-wiki.no
(Created page with "= ASA 2 = ASA 2 Connection Return to the Technology page.") |
|||
(One intermediate revision by the same user not shown) | |||
Line 2: | Line 2: | ||
[[File:ASA_2_connection.png|center|ASA 2 Connection]] | [[File:ASA_2_connection.png|center|ASA 2 Connection]] | ||
+ | |||
+ | |||
+ | == Initial setup == | ||
+ | ASA 2 came with NexTelCoASA configuration. These are the steps we followed to save the configuration: | ||
+ | NexTelCoASA(config)#copy startup-config disk0: | ||
+ | Destination filename [startup-config]?NexTelCoASA_startup-config_20140522 | ||
+ | NexTelCoASA(config)#copy running-config disk0: | ||
+ | Destination filename [startup-config]?NexTelCoASA_running-config_20140522 | ||
+ | NexTelCoASA#write erase | ||
+ | Erase configuration in flash memory? [confirm] | ||
+ | NexTelCoASA#reload | ||
+ | Proceed with reload? [confirm] | ||
+ | After saving the configuration and recoverying its initial state, ASA starts with the oldest image it finds in disk0. In this case the ASA software version 7.2(3) and ASDM version 5.2(3). If there is any newer software version is convenient to change it. These are followed step. | ||
+ | ciscoasa(config)#boot system disk0:/asa805-k8.bin | ||
+ | ciscoasa(config)#asdm image disk0:/asdm-623.bin | ||
+ | ciscoasa#write memory | ||
+ | ciscoasa#reload | ||
+ | After this change, ASA is working with '''software version 8.0(5) and ASDM 6.2(3)'''. | ||
+ | |||
+ | |||
+ | == Specifications == | ||
+ | This device has the following specifications: | ||
+ | * Hardware | ||
+ | **ASA5505 | ||
+ | **256MB RAM | ||
+ | **CPU Geode 500 MHz | ||
+ | **Internal ATA Compact Flash 128MB | ||
+ | **BIOS Flash M50FW080 @ 0xffe00000 1024KB | ||
+ | * Licensed features for this platform: | ||
+ | ** Maximum Physical Interfaces : 8 | ||
+ | ** VLANs : 3, DMZ Restricted | ||
+ | ** Inside Hosts : Unlimited | ||
+ | ** Failover : Disabled | ||
+ | ** VPN-DES : Enabled | ||
+ | ** VPN-3DES-AES : Enabled | ||
+ | ** VPN Peers : 10 | ||
+ | ** WebVPN Peers : 2 | ||
+ | ** Dual ISPs : Disabled | ||
+ | ** VLAN Trunk Ports : 0 | ||
+ | ** AnyConnect for Mobile : Disabled | ||
+ | ** AnyConnect for Linksys phone : Disabled | ||
+ | ** Advanced Endpoint Assessment : Disabled | ||
+ | ** UC Proxy Sessions : 2 | ||
+ | * This platform has a Base license. | ||
+ | * Serial Number : JMX1151Z0N8 | ||
+ | |||
+ | |||
+ | == Configuration == | ||
+ | The official configuration guide for this software version, 8.0(5) can be found [http://www.cisco.com/c/en/us/td/docs/security/asa/asa80/configuration/guide/conf_gd.html here.] | ||
Return to the [[Nextelco:Technology|Technology]] page. | Return to the [[Nextelco:Technology|Technology]] page. |
Latest revision as of 15:12, 25 May 2014
ASA 2
Initial setup
ASA 2 came with NexTelCoASA configuration. These are the steps we followed to save the configuration:
NexTelCoASA(config)#copy startup-config disk0: Destination filename [startup-config]?NexTelCoASA_startup-config_20140522 NexTelCoASA(config)#copy running-config disk0: Destination filename [startup-config]?NexTelCoASA_running-config_20140522 NexTelCoASA#write erase Erase configuration in flash memory? [confirm] NexTelCoASA#reload Proceed with reload? [confirm]
After saving the configuration and recoverying its initial state, ASA starts with the oldest image it finds in disk0. In this case the ASA software version 7.2(3) and ASDM version 5.2(3). If there is any newer software version is convenient to change it. These are followed step.
ciscoasa(config)#boot system disk0:/asa805-k8.bin ciscoasa(config)#asdm image disk0:/asdm-623.bin ciscoasa#write memory ciscoasa#reload
After this change, ASA is working with software version 8.0(5) and ASDM 6.2(3).
Specifications
This device has the following specifications:
- Hardware
- ASA5505
- 256MB RAM
- CPU Geode 500 MHz
- Internal ATA Compact Flash 128MB
- BIOS Flash M50FW080 @ 0xffe00000 1024KB
- Licensed features for this platform:
- Maximum Physical Interfaces : 8
- VLANs : 3, DMZ Restricted
- Inside Hosts : Unlimited
- Failover : Disabled
- VPN-DES : Enabled
- VPN-3DES-AES : Enabled
- VPN Peers : 10
- WebVPN Peers : 2
- Dual ISPs : Disabled
- VLAN Trunk Ports : 0
- AnyConnect for Mobile : Disabled
- AnyConnect for Linksys phone : Disabled
- Advanced Endpoint Assessment : Disabled
- UC Proxy Sessions : 2
- This platform has a Base license.
- Serial Number : JMX1151Z0N8
Configuration
The official configuration guide for this software version, 8.0(5) can be found here.
Return to the Technology page.