LNCC RPI testing
Wiki for ITS | ||||||
---|---|---|---|---|---|---|
|
![]() |
Contents
⌘ Testing of LNCC and RPI
Connect the cables as indicated in figure 1
⌘ Testing the antenna
⌘ Connecting the system to the Internet
Perform an initial testing, by
- connecting port 1 of the LNCC to either a fixed Internet or to the antenna. If you use the antenna, make sure you have tested connectivity to the antenna first
4) Deployment on site
This chapter is part of the DigI:Processes_and_Technology, and describes the initial testing on arrival, as well as the deployment in the field. Note: Before you go out in the field, perform the test on arrival to make sure the equipment works.
4.1 Test on arrival
After receiving the equipment from the customs office, an initial test needs to be accomplished for the equipment set. Everything is reconfigured, allowing that you can add a SIM card to the LTE antenna, and then go through the test. Note: Ensure that the SIM card does not have a PIN code
For equipment going out to the communities, the initial needs to be accomplished at a site where Mobile Broadband (3G, 4G) is available. The test plans are provided by Wisam to accompany the testing.
- (1) InitialTesting_with cables.pdf original on owncloud in DeviceConfig
- (2) Detailed TestPlan(.pdf) original on owncloud in DeviceConfig
All the boxes are pre-configured - the following info is needed in case the boxes are not cabled.
- SIM card: you need to purchase a local SIM card, suggest to work with 5-10 GByte data package. Ensure to remove the PIN code, otherwise the LTE Antenna can't work with the SIM. Note: use a normal phone to remove the PIN: Android = Settings = Device security = SIM card lock = Lock SIM card (off).
- LTE Antenna: insert SIM card, connect cables, POE, power source test, and check that lights are working. A detailed connecting and testing document is available on OwnCloud (see Figure 4.1 or (1) InitialTesting Overview)
- The LTE antenna and the LNCC have different power supplies. The LTE antenna needs 24 V, 1.2 A power, while the LNCC works with 24 V, 0.8 A (see Figure 4.3). Make sure not to mix, otherwise your powersupply is getting burned
- LNCC router: connect the Internet wire coming from the LTE to port 1 on the LNCC, connect the LNCC to a power source, and check if the power light is lightning green on the backside, in order to establish a local network /wifi.
- Village server/ RPI: connect the RPI to electricity using the charger, normal Samsung mobile charger, and check if the power light is blinking/on. Then, connect the PRI to port 2 on the LNCC using an Internet wire.
- When all the equipment are well connected to each other and the electricity the person should check on his mobile/ Tablet the accessibility of the Basic Internet network.
Success: I can connect, next step implementation in the site and testing 4.2.
Failure: I can't connect, go to step 4.3.4. - Test the village platform by opening your browser and open the website yeboo.com, or what has been specified for the specific village your are testing its spot:
Success: I can reach the site and the videos, next step 4.2,
Failure: I can't reach. the reason could be:
- a) check the RPI connection to LNCC on port 2, and electricity, if that is well connected.
- b) check with Wisam or Hamed if the RPI is identified to work with the used LNCC
- c) check with Wisam or Maurice that the main server of the village platform is working
- d) open the RPI case and check the small lights beside the USB, red and green lights, if they aren't working that means no power and Internet are reaching the RPI otherwise if reason a) was checked well that indicates the RPI is dead and should be replaced with a new one take contact with Wisam
- If the information spot providing wifi and the village platform is accessible, then, the set will be shipped to its final destination, the targeted village.
4.2 Testing in the field
After arrival at the site, connect the equipment and perform a functionality testing before raising the pole. Connect the equipment in the same way in step 4.1 and repeat all the tests to ensure getting the connection to the Basic Internet network and the village platform.
4.3 Error testing in the field
When the equipment (LTE, LNCC, Village server) are deployed in the field, the user should be able to perform simple steps to check the configurability. Through our central equipment, we are able to connect remotely to the LNCC and the RPI (if they are on the network).
A user being at the the site can test the following:
- 4.3.1. I look for Wifi "BasicInternet", and connect to Wifi.
Success: I can connect, next step 4.3.2.
Failure: I can't connect, go to step 4.3.4. - 4.3.2. - only if the Raspberry Pi is connected on port 2 - The user opens a browser (e.g. Chrome) and connects to Yeboo.com (or Yeboo)
Success: The health information page (see Figure 1) is shown, and the hotspot works as planned
Failure: Web site not found. Goto step 4.3.3.
- 4.3.3. In the Web browser, type google.com.
YES: Google is working, network access. Test Yeboo.com. If still not connected to the health site, probably the Raspberry PI is dead, or a configuration team. Contact the BasicInternet Team
NO: if google.com is not shown, then we have no network access.
- Try the following Web sites: 10.5.50.1 - if successful, it means that the network connectivity is established (?)
- basicinternet.org - we have full network access
- Google.co.tz
- if these sites are not working, then we have the potential problems:
- No credit on the SIM card,
- SIM card is locked by PIN code (see above how to fix)
- Devices not working,
- Cables unconnected/loose
the LTE/UMTS network is down. Use the "network cell info light" App (Google Play) to see if a mobile network is up.
- 4.3.4 Check the equipment: Is the light blinking at the back of the LNCC?
NO: no power or LNCC is dead.
YES: Lights are blinking. Reboot the LNCC: disconnect the power, reconnect and see if the lights come up. Check if you have electricity. If the LNCC still does not work, we need to replace it (step 4.4)
Question: What happens if the RPI is "dead", what will the user see when typing Yeboo.com?
- A: If the Raspberry Pi is dead/no power, and we type Yeboo.com, we'll get address not found
4.4 process for replacement
- Please describe the problem in our GDocs: https://docs.google.com/document/d/1E2U9N_ivFB-gnHk1-m00lNiMjzATuXhOhBnoWQYzLvc/edit?usp=sharing
- Get into contact with the Foundation, Wisam or "mail to info@BasicInternet.org"
Before you do so, please make sure that all LNCCs and the corresponding RPIs are connected through cables and powered on
⌘ Testing the RPI
⌘ Testing the LNCC
⌘ Creating and testing vouchers
see http://voucher.basicinternet.no on how to create vouchers. * Create a voucher, e.g. validity 1 h (or 100 MB)