Difference between revisions of "CITI-Sense-Mob sensor testing"
Josef.Noll (Talk | contribs) (Created page with "{{Meeting |Title=CITI-Sense-Mob sensor testing |Place=UNIK |Date=2014/03/03 |Duration=0900-1100 |Organiser=Josef Noll, |Project=Citi-Sense-MOB, |User=Seraj Fayyad, }} = Sta...") |
Josef.Noll (Talk | contribs) |
||
(23 intermediate revisions by 2 users not shown) | |||
Line 4: | Line 4: | ||
|Date=2014/03/03 | |Date=2014/03/03 | ||
|Duration=0900-1100 | |Duration=0900-1100 | ||
− | |Organiser=Josef Noll, | + | |Organiser=Josef Noll, |
− | |Project=Citi-Sense-MOB, | + | |Project=Citi-Sense-MOB, |
− | |User=Seraj Fayyad, | + | |Depiction=EB700 Operating Manual Ver2.doc,CitiMobileBike.pptx, |
+ | |User=Seraj Fayyad, | ||
}} | }} | ||
+ | __NOTOC__ | ||
= Status = | = Status = | ||
− | + | 1) earlier tests failed, no sensor signal | |
Potential reasons | Potential reasons | ||
Line 16: | Line 18: | ||
* communication fails | * communication fails | ||
* | * | ||
+ | |||
+ | On-device monitoring | ||
+ | * Tested the sensor with usb directly to pc and checked that there is some communication in a terminal program | ||
+ | * Also, open it and recheck if the sim card is correctly in the slot. | ||
+ | |||
+ | 2) second test partially success, no location information, show some measured values | ||
+ | |||
+ | Potential reasons: | ||
+ | * static electricity | ||
+ | |||
+ | Done activities: | ||
+ | * Send SMS to sensor SIM card (40923931), content =<SRVADR>srv.dunavnet.eu</SRVADR> | ||
+ | (goal): change server address to the new one. | ||
+ | * Sensor discharging from static electricity. | ||
+ | * Sensor running without SIM card then with SIM card in order | ||
+ | (goal): force sensor to recheck the SIM card existence | ||
+ | |||
+ | 3) third test: Temporal success with location identification and measurements : | ||
+ | |||
+ | location identification failed potential reasons: | ||
+ | * some wire bad connectivity. | ||
+ | |||
+ | Done activities: | ||
+ | * recheck wires connectivity | ||
+ | * static electricity discharging. | ||
+ | * Partial testing for different parts of the sensor. | ||
+ | |||
+ | 4) fourth test: | ||
+ | Without air sensors board the sensor send approximately half of the expected number of sending | ||
+ | |||
+ | Done activities | ||
+ | * Running of sensor without embedded air quality sensors board for four hours. | ||
+ | |||
+ | Result: | ||
+ | * sensor send 114 reading pre 4 hour where sensor settings were configured to send sense read every 1 min. | ||
+ | |||
+ | |||
+ | |||
+ | (Notes): | ||
+ | * The sensor needs 15 after turn it on to stabilize its sensing and to provide reliable data. | ||
+ | * Air quality embedded sensors need to be exchanged with new one every 2 year. | ||
+ | |||
+ | caution: | ||
+ | sensor used techs for air contents measurement based on the using of ACID (harmful chemical substance) which sometimes cause bad smell. | ||
+ | |||
+ | Needed for future testing: | ||
+ | * list of used commands for sensor configuration in order to simplify and accelerate testing. | ||
+ | * Mobile SIM card for sensors configuration. | ||
+ | * Sensor manual (uploaded) | ||
= Dunavnet link = | = Dunavnet link = | ||
− | + | Dunavnet | |
− | http://srv.dunavnet.eu/rephandler/ecodb/select%20top%2010%20*%20from%20dbo.history_data%20where%20bus_identifier%20=%20%20'355255040040264'%20%20order%20by%20timestamp_device%20desc | + | [http://srv.dunavnet.eu/rephandler/ecodb/select%20top%2010%20*%20from%20dbo.history_data%20where%20bus_identifier%20=%20%20'355255040040264'%20%20order%20by%20timestamp_device%20desc|Device 3 online data] |
+ | |||
+ | [[File:Screenshot_Dunavnet_Sensor3.png|400px|right]] | ||
+ | GUI | ||
+ | * http://citisense.dunavnet.eu/index.php?id=3 | ||
+ | |||
+ | |||
+ | Last measured: | ||
+ | * http://srv.dunavnet.eu/rephandler/ecobus/355255040040264 | ||
+ | * dunavnet - citisense!3 | ||
+ | * | ||
+ | |||
+ | Raw data from WFS server | ||
+ | * sensor 4 (.xml): [http://ec2-54-171-68-180.eu-west-1.compute.amazonaws.com:8080/citisense/webproxy/allmeasurements/sensorid/194001.xml] | ||
+ | |||
+ | == Link status == | ||
+ | * lab testing 20Dec2013, position: 59.9755117, 11.0535750 (NILU lab) | ||
+ | [[File:Position_external_sensor3.png|400px]] | ||
+ | |||
+ | ---- | ||
+ | internal sensor measures: [[Air_Quality_bike_sensor_parameter]] |
Latest revision as of 10:22, 4 November 2014
Wiki for ITS | ||||||
---|---|---|---|---|---|---|
|
CITI-Sense-Mob sensor testing
Title | CITI-Sense-Mob sensor testing |
---|---|
Place | UNIK |
Date, Time | 2014/03/03, 0900-1100 |
Contact Person | Josef Noll |
Participants | Seraj Fayyad |
related to Project | Citi-Sense-MOB |
Keywords |
this page was created by Special:FormEdit/Meeting, and can be edited by Special:FormEdit/Meeting/CITI-Sense-Mob sensor testing |
Category:Meeting |
Status
1) earlier tests failed, no sensor signal
Potential reasons
- no power supply, - measure with multimeter
- to little power (effect) to fire up the sensor board - - don't know the power
- communication fails
On-device monitoring
- Tested the sensor with usb directly to pc and checked that there is some communication in a terminal program
- Also, open it and recheck if the sim card is correctly in the slot.
2) second test partially success, no location information, show some measured values
Potential reasons:
- static electricity
Done activities:
- Send SMS to sensor SIM card (40923931), content =<SRVADR>srv.dunavnet.eu</SRVADR>
(goal): change server address to the new one.
- Sensor discharging from static electricity.
- Sensor running without SIM card then with SIM card in order
(goal): force sensor to recheck the SIM card existence
3) third test: Temporal success with location identification and measurements :
location identification failed potential reasons:
- some wire bad connectivity.
Done activities:
- recheck wires connectivity
- static electricity discharging.
- Partial testing for different parts of the sensor.
4) fourth test: Without air sensors board the sensor send approximately half of the expected number of sending
Done activities
- Running of sensor without embedded air quality sensors board for four hours.
Result:
- sensor send 114 reading pre 4 hour where sensor settings were configured to send sense read every 1 min.
(Notes):
* The sensor needs 15 after turn it on to stabilize its sensing and to provide reliable data. * Air quality embedded sensors need to be exchanged with new one every 2 year.
caution: sensor used techs for air contents measurement based on the using of ACID (harmful chemical substance) which sometimes cause bad smell.
Needed for future testing:
- list of used commands for sensor configuration in order to simplify and accelerate testing.
- Mobile SIM card for sensors configuration.
- Sensor manual (uploaded)
Dunavnet 3 online data
GUI
Last measured:
- http://srv.dunavnet.eu/rephandler/ecobus/355255040040264
- dunavnet - citisense!3
Raw data from WFS server
- sensor 4 (.xml): [1]
Link status
- lab testing 20Dec2013, position: 59.9755117, 11.0535750 (NILU lab)
internal sensor measures: Air_Quality_bike_sensor_parameter