Difference between revisions of "CITI-Sense-Mob sensor testing"
From its-wiki.no
Seraj.Fayyad (Talk | contribs) (→Status) |
Josef.Noll (Talk | contribs) |
||
| (10 intermediate revisions by 2 users not shown) | |||
| Line 6: | Line 6: | ||
|Organiser=Josef Noll, | |Organiser=Josef Noll, | ||
|Project=Citi-Sense-MOB, | |Project=Citi-Sense-MOB, | ||
| + | |Depiction=EB700 Operating Manual Ver2.doc,CitiMobileBike.pptx, | ||
|User=Seraj Fayyad, | |User=Seraj Fayyad, | ||
}} | }} | ||
| Line 28: | Line 29: | ||
Done activities: | Done activities: | ||
| − | * Sensor discharging from static electricity | + | * Send SMS to sensor SIM card (40923931), content =<SRVADR>srv.dunavnet.eu</SRVADR> |
| + | (goal): change server address to the new one. | ||
| + | * Sensor discharging from static electricity. | ||
* Sensor running without SIM card then with SIM card in order | * Sensor running without SIM card then with SIM card in order | ||
(goal): force sensor to recheck the SIM card existence | (goal): force sensor to recheck the SIM card existence | ||
| − | 3) third test success with location identification and measurements: | + | 3) third test: Temporal success with location identification and measurements : |
| + | |||
location identification failed potential reasons: | location identification failed potential reasons: | ||
* some wire bad connectivity. | * some wire bad connectivity. | ||
| Line 41: | Line 45: | ||
* Partial testing for different parts of the sensor. | * Partial testing for different parts of the sensor. | ||
| + | 4) fourth test: | ||
| + | Without air sensors board the sensor send approximately half of the expected number of sending | ||
| + | |||
| + | Done activities | ||
| + | * Running of sensor without embedded air quality sensors board for four hours. | ||
| + | |||
| + | Result: | ||
| + | * sensor send 114 reading pre 4 hour where sensor settings were configured to send sense read every 1 min. | ||
| + | |||
| + | |||
| + | |||
| + | (Notes): | ||
| + | * The sensor needs 15 after turn it on to stabilize its sensing and to provide reliable data. | ||
| + | * Air quality embedded sensors need to be exchanged with new one every 2 year. | ||
caution: | caution: | ||
| − | sensor used techs for air contents measurement based on the using of ACID (chemical substance) | + | sensor used techs for air contents measurement based on the using of ACID (harmful chemical substance) which sometimes cause bad smell. |
| + | |||
| + | Needed for future testing: | ||
| + | * list of used commands for sensor configuration in order to simplify and accelerate testing. | ||
| + | * Mobile SIM card for sensors configuration. | ||
| + | * Sensor manual (uploaded) | ||
= Dunavnet link = | = Dunavnet link = | ||
| Line 56: | Line 79: | ||
Last measured: | Last measured: | ||
* http://srv.dunavnet.eu/rephandler/ecobus/355255040040264 | * http://srv.dunavnet.eu/rephandler/ecobus/355255040040264 | ||
| − | + | * dunavnet - citisense!3 | |
| + | * | ||
| + | |||
| + | Raw data from WFS server | ||
| + | * sensor 4 (.xml): [http://ec2-54-171-68-180.eu-west-1.compute.amazonaws.com:8080/citisense/webproxy/allmeasurements/sensorid/194001.xml] | ||
== Link status == | == Link status == | ||
Latest revision as of 10:22, 4 November 2014
| Wiki for ITS | ||||||
|---|---|---|---|---|---|---|
|
|
CITI-Sense-Mob sensor testing
| Title | CITI-Sense-Mob sensor testing |
|---|---|
| Place | UNIK |
| Date, Time | 2014/03/03, 0900-1100 |
| Contact Person | Josef Noll |
| Participants | Seraj Fayyad |
| related to Project | Citi-Sense-MOB |
| Keywords |
| this page was created by Special:FormEdit/Meeting, and can be edited by Special:FormEdit/Meeting/CITI-Sense-Mob sensor testing |
| Category:Meeting |
Status
1) earlier tests failed, no sensor signal
Potential reasons
- no power supply, - measure with multimeter
- to little power (effect) to fire up the sensor board - - don't know the power
- communication fails
On-device monitoring
- Tested the sensor with usb directly to pc and checked that there is some communication in a terminal program
- Also, open it and recheck if the sim card is correctly in the slot.
2) second test partially success, no location information, show some measured values
Potential reasons:
- static electricity
Done activities:
- Send SMS to sensor SIM card (40923931), content =<SRVADR>srv.dunavnet.eu</SRVADR>
(goal): change server address to the new one.
- Sensor discharging from static electricity.
- Sensor running without SIM card then with SIM card in order
(goal): force sensor to recheck the SIM card existence
3) third test: Temporal success with location identification and measurements :
location identification failed potential reasons:
- some wire bad connectivity.
Done activities:
- recheck wires connectivity
- static electricity discharging.
- Partial testing for different parts of the sensor.
4) fourth test: Without air sensors board the sensor send approximately half of the expected number of sending
Done activities
- Running of sensor without embedded air quality sensors board for four hours.
Result:
- sensor send 114 reading pre 4 hour where sensor settings were configured to send sense read every 1 min.
(Notes):
* The sensor needs 15 after turn it on to stabilize its sensing and to provide reliable data. * Air quality embedded sensors need to be exchanged with new one every 2 year.
caution: sensor used techs for air contents measurement based on the using of ACID (harmful chemical substance) which sometimes cause bad smell.
Needed for future testing:
- list of used commands for sensor configuration in order to simplify and accelerate testing.
- Mobile SIM card for sensors configuration.
- Sensor manual (uploaded)
Dunavnet 3 online data
GUI
Last measured:
- http://srv.dunavnet.eu/rephandler/ecobus/355255040040264
- dunavnet - citisense!3
Raw data from WFS server
- sensor 4 (.xml): [1]
Link status
- lab testing 20Dec2013, position: 59.9755117, 11.0535750 (NILU lab)
internal sensor measures: Air_Quality_bike_sensor_parameter
